Body Prep 1

Used Raptor Bed Liner (link below) – goes on very easily with the supplied air gun and comes off the fiberglass with acetone… 11-24-20 -Greg Roselli

https://smile.amazon.com/gp/product/B01CKE7B1E

Trunk Aluminum

Fitting it in is like a bar puzzle but it’s doable. Access panel link below. Waiting till the very last minute to attach permanently… 11-24-20 -Greg Roselli

https://www.circletracksupply.com/aluminum-access-panels.html

More Wiring, Passenger Seat Mount, Belts

Tail lights & headlights, cleaned up the amp wiring, mounted the passenger seat and installed Simpson 5-point belts. Jeep Wrangler headlights seem to get the job done here according to other builders. 11-24-2020 -Greg Roselli

https://smile.amazon.com/gp/product/B01MTXNED5

https://smile.amazon.com/Simpson-Racing-29073BK-Pull-Down-Individual/dp/B0006HLT0M

Radio, Wiring, Rear Cam, More Aluminum

Been a slow year but I’m back at it… Radio equipment and rearview mirror links below, we’ll see if it’s loud enough while the engine is on. Continuing prep work to put body on… -Greg Roselli 4-27-20

https://smile.amazon.com/gp/product/B00J863EI2/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

https://smile.amazon.com/gp/product/B004VSTYI6/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

https://smile.amazon.com/gp/product/B004VBK860/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

https://smile.amazon.com/gp/product/B004T0WFVE/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

0322201703 0322201703a 0322201703b 0322201703c 0322201703d 0322201703e 0413201608 0425201716 0425201717 0425201717a 0425201726 0426201409 0426201451

AC Charging, Alignment

Left the nest to get the AC charged and car aligned while it was still open. Rolling chassis is officially complete. Thanks to https://www.artiesgarage.com/ Still a lot of work ahead…. -Greg Roselli 5-2-19

Dashboard, remaining wiring

Cut holes in dash for remaining gauges, switches and AC vents. Installed Russ Thompson turn signal system (http://www.norcal-cobras.com/store/russ_garage/t65/t65tss.html). Completed wiring. 2nd test run. April 15, 2019 -Greg Roselli

0203191418 0224191523 0224191523a 0224191613 0407191623 0407191623a 0407191624 0407191624a

0413191547 0413191547a 0413191547b 0413191547c 0413191547d 0413191547e 0413191547f 0413191600b 0413191600c

REMAINING AC; DASHBOARD; GAUGES

It’s possible I forgot to post here for 5 months. Remaining AC work, trinary safety switch, condenser and controls. Dash board cut and placement, initial gauge wiring. Details in photo comments.

Astro rivnut tool https://smile.amazon.com/gp/product/B003TODXQW/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

FFR Gauges http://www.factoryfiveparts.com/60311-type-65-coupe-gps-gauge-set-mph/

December 3, 2018 – Greg Roselli

Remaining AC:

Dashboard/Gauges:

AC HOSES, part 1

Routing the AC hoses, part 1. Had to buy additional Vintage Air Beadlock Heater Fittings and and a Mastercool Manual A/C Hose Crimper on amazon (https://smile.amazon.com/gp/product/B000WBQ4U2/ref=oh_aui_detailpage_o09_s04?ie=UTF8&psc=1). Also had a special guest in the workshop. June 24, 2018 -Greg Roselli

LizardSkin, AC kickoff

Applied LizardSkin Ceramic Thermal Insulation Coating (https://www.lizardskin.com/car-ceramic-insulation.html) to the interior with a 4″ roller vs. a spray. Mounted AC condenser and began install of Vintage Air Mini Space Saver AC/Heat/Defrost unit (https://www.vintageair.com/) May 20, 2018 -Greg Roselli